Allied Telesis AT-FS201 Installation Guide

AT-FS201AT-FS202AT-FS202SC/FS1Bridging Media ConvertersVersion 4Installation GuidePN 613-000400 Rev A

PrefacexContacting Allied TelesynThis section provides Allied Telesyn contact information for technical support as well as sales or corporate informat

1Chapter 1OverviewThe AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters include the following models: AT-FS201 AT-FS202 AT-FS202SC/F

Chapter 1: Overview2IntroductionThe fiber optic port on the bridging converter offers an important advantage over fiber optic ports commonly found on

AT-FS20x Series Installation Guide3The port can simultaneously send and receive Ethernet packets using the same wavelength of 1310 nm for both data st

Chapter 1: Overview4Bridging Media Converter ComponentsFigure 4 shows the front panel of the AT-FS201 Bridging Media Converter.Figure 4. AT-FS201 Fron

AT-FS20x Series Installation Guide5The back panel of the AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters features a DC power connecto

Chapter 1: Overview6External Power SupplyThe 12VDC-version converters come with the AC/DC power adapter, shown in Figure 8. This is an approved safety

AT-FS20x Series Installation Guide7Key FeaturesThe AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters have the following features: LEDs

Chapter 1: Overview8Status LEDsTable 2 defines the LEDs for the AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters.Table 2. Status LEDsL

AT-FS20x Series Installation Guide9Twisted Pair PortThe AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters have one 10Base-T/100Base-TX

Copyright © 2006 Allied Telesyn, Inc.www.alliedtelesyn.comAll rights reserved. No part of this publication may be reproduced without prior written per

Chapter 1: Overview10Auto MDI/MDI-XAn RJ-45 twisted pair port on a 10 Mbps or 100 Mbps Ethernet network device can have one of two possible wiring con

AT-FS20x Series Installation Guide11Fiber Optic PortThe AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters have one 100Base-FX fiber opt

Chapter 1: Overview12Bridging Media Converter PerformanceThe bridging media converters perform at: 148,800 pps for 100 Mbps and 14,880 pps for 10 Mbp

AT-FS20x Series Installation Guide13DIP SwitchesThe DIP switches are used to manually configure the operating characteristics of the ports, such as po

Chapter 1: Overview14MAC Address TableUp to 512 MAC addresses can be stored in the converter’s MAC address table. The converter’s self-learning featur

AT-FS20x Series Installation Guide15Store and ForwardThe AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters support store and forward sw

Network TopologyFigure 9 illustrates a topology using one AT-FS202 Bridging Media Converter to interconnect two small networks of stakable hubs. Netw

17Chapter 2InstallationThis chapter explains how to install the AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters. These converters can

Chapter 2: Installation18Planning the InstallationBe sure to observe the following guidelines when planning the installation of your converter. The e

AT-FS20x Series Installation Guide19AT-FS202 50/125 or 62.5/125 micron multimode2 km (1.24 mi)9.3dB @ 1310nm (50/125 MMF)12.8dB @ 1310nm(62.5/125 MMF)

iiiElectrical Safety and Emission Compliance StatementStandards: This product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A

Chapter 2: Installation20Selecting a SiteBe sure to observe the following guidelines when selecting a site for your converter. Select a site that is

AT-FS20x Series Installation Guide21Reviewing Safety GuidelinesPlease review the following safety guidelines before you begin to install the converter

Chapter 2: Installation22CautionOperating Temperature: This product is designed for a maximum ambient temperature of 40°C.  9CautionAll Countries: In

AT-FS20x Series Installation Guide23Installing the Bridging Media ConverterThe AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters can be

Chapter 2: Installation24NoteDo not attach the protective feet if you are wallmounting the unit, installing it in an AT-WLMT-010 wallmount bracket or

AT-FS20x Series Installation Guide25When setting the DIP switches, consider the following: Setting the Auto Neg DIP switch for the twisted pair port

Chapter 2: Installation26NoteThis step does not apply if you are mounting a 12VDC-version converter in an AT-MCR12 chassis.For instructions on how to

AT-FS20x Series Installation Guide27You should check to be sure that you are using the appropriate type of twisted pair cabling. Refer to Table 3 on

Chapter 2: Installation28Connecting a 12VDC Powered UnitTo apply power to a 12VDC version converter, perform the following steps:NoteThe power adapter

AT-FS20x Series Installation Guide29Warranty RegistrationWhen you finish installing the product, you should register your product by completing the en

Electrical Safety and Emission Compliance StatementivImportant: Appendix C contains translated safety statements for installing this equipment. When

31Chapter 3TroubleshootingFollow the guidelines below to test and troubleshoot the installation in the event a problem occurs.NoteIf you change the sp

Chapter 3: Troubleshooting32cable for 10Base-T operation or a Category 5 or better cable for 100Base-TX operation. If the twisted pair port is set to

AT-FS20x Series Installation Guide33Check that the operating specifications of the fiber optic port on the end-node are compatible with the operating

35Appendix ATechnical SpecificationsPhysicalDimensions: W x D x H10.5 cm x 9.5 cm x 2.5 cm(4.125 in x 3.75 in x 1.0 in)Weight: .27 kg (0.60 lbs)Temper

Appendix A: Technical Specifications36Agency CertificationsRFI Emissions FCC Part 15 Class A, EN55022 Class AImmunity EN55024Electrical Safety UL 6095

AT-FS20x Series Installation Guide37RJ-45 Twisted Pair Port PinoutsFigure 12 shows the pin layout to an RJ-45 connector and port.Figure 12. RJ-45 Conn

Appendix A: Technical Specifications38Fiber Optic Port SpecificationsTable 8. Fiber Optic Loss Specifications (Benchmarks)Fiber Type11. MMF = Multimod

AT-FS20x Series Installation Guide39Table 11. Fiber Optic DatalinkModelFiber Optic Type1Max. Power / Link BudgetMin. Distance Spec.2Max. Distance Spec

vContentsElectrical Safety and Emission Compliance Statement ...iiiPreface ...

41Appendix BCleaning Fiber Optic ConnectorsThis section describes how to clean fiber optic connections. The fiber optic connector consists of a fiber

Appendix B: Cleaning Fiber Optic Connectors42This appendix provides the following procedures: “Using a Cartridge-Type Cleaner” on page 42 “Using a S

AT-FS20x Series Installation Guide432. Place the ferrule tip on the exposed cleaning surface and rub the ferrule in a downward direction, as shown in

Appendix B: Cleaning Fiber Optic Connectors44NoteDo not touch the end face of the ferrule in the connector.WarningDo not stare into the laser beam. 2

AT-FS20x Series Installation Guide45To clean a recessed ferrule using a swab, perform the following procedure.1. Insert the swab into the adapter as s

47Appendix CTranslated Electrical, Safety, and Emission InformationImportant: This appendix contains multiple-language translations for the safety sta

Appendix C: Translated Electrical, Safety, and Emission Information48Laser Safety NoticesElectrical Safety Notices1 Warning: Class 1 Laser product.2 W

AT-FS20x Series Installation Guide4911 Warning: As a safety precaution, install a circuit breaker with a minimum value of 20 Amps between the equipmen

ContentsviChapter 2Installation ... 17Verifying

Appendix C: Translated Electrical, Safety, and Emission Information5021 Warning: The power source for the gateway unit should be located near the unit

AT-FS20x Series Installation Guide5131 Warning: Do not look directly at the fiber optic cable ends or inspect the cable ends with an optical lens.32 W

Appendix C: Translated Electrical, Safety, and Emission Information52Telecommunications Compliance Notices41 Warning: When using your telephone equipm

AT-FS20x Series Installation Guide53LasersicherheitshinweiseElektrische Sicherheitshinweise1 Achtung: Laserprodukt der Klasse 1.2 Achtung: Blicken Sie

Appendix C: Translated Electrical, Safety, and Emission Information5411 Achtung: Als Sicherheitsvorkehrung sollte ein Ьberlastschalter mit einem minim

AT-FS20x Series Installation Guide5520 Vorsicht: Bei der Innenraummontage des Gateway-Gerдts ist darauf zu achten, dass es in einer staubfreien Umgebu

Appendix C: Translated Electrical, Safety, and Emission Information5629 Zur zuverlдssigen Stromversorgung des Gerдts sollte ein dedizierter Stromkreis

AT-FS20x Series Installation Guide57Telekommunikationskonformitдtshinweise41 Achtung: Bei der Verwendung Ihrer Telefonausrьstung sollten zur Reduzieru

Appendix C: Translated Electrical, Safety, and Emission Information58Avisos de seguridad láserAvisos de seguridad elйctricas1Atenciуn: Producto lбser

AT-FS20x Series Installation Guide5911 Atenciуn: Como medida de seguridad, instale un disyuntor con un valor mнnimo de 20 A entre el equipo y la toma

viiPrefaceThis guide contains instructions on how to install an AT-FS201, AT-FS202, and AT-FS202SC/FS1 Bridging Media Converters. How This Guide is Or

Appendix C: Translated Electrical, Safety, and Emission Information6021 Atenciуn: La toma elйctrica de la unidad de puerta de enlace debe estar situad

AT-FS20x Series Installation Guide6132 Atenciуn: Esta unidad puede tener mбs de un cable de alimentaciуn. Para reducir el peligro de electrocuciуn, de

Appendix C: Translated Electrical, Safety, and Emission Information62Avisos de conformidad de telecomunicaciones41 Atenciуn: Cuando utilice su equipo

AT-FS20x Series Installation Guide63Avis de sécurité laserAvis de sйcuritй йlectrique1 Avertissement: Produit laser de classe 1.2 Avertissement: Ne pa

Appendix C: Translated Electrical, Safety, and Emission Information6411 Avertissement: Par mesure de sйcuritй, installer un coupe-circuit d’une intens

AT-FS20x Series Installation Guide6520 Attention: Si le pйriphйrique servant de passerelle est installй а l’intйrieur, s’assurer qu’il se trouve dans

Appendix C: Translated Electrical, Safety, and Emission Information6629 Utiliser des circuits d’alimentation ou des unitйs de conditionnement dйdiйs p

AT-FS20x Series Installation Guide67Tйlйcommunications – Avis de conformitй41 Avertissement: Les prйcautions йlйmentaires de sйcuritй doivent кtre sys

Appendix C: Translated Electrical, Safety, and Emission Information68Indicazioni sulla sicurezza laserIndicazioni sulla sicurezza elettrica1 Avvertenz

AT-FS20x Series Installation Guide6911 Avvertenza: Per precauzione, installare un salvavita con un valore minimo di 20 ampere tra l'apparecchiatu

PrefaceviiiDocument ConventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that p

Appendix C: Translated Electrical, Safety, and Emission Information7021 Avvertenza: La fonte di alimentazione dell'unitа gateway deve essere posi

AT-FS20x Series Installation Guide7132 Avvertenza: Questa unitа potrebbe disporre di piщ cavi di alimentazione. Per ridurre il rischio di scosse elett

Appendix C: Translated Electrical, Safety, and Emission Information72Indicazioni per la conformitа con le norme sulle telecomunicazioni41 Avvertenza:

AT-FS20x Series Installation Guide73Лазерная безопасностьЭлектрическая безопасность1 Внимание: лазерный продукт, класс 1.2 Внимание: Не смотрите прямо

Appendix C: Translated Electrical, Safety, and Emission Information7410 Во всех странах: Инсталлируйте продукт в соответствии с национальными нормами

AT-FS20x Series Installation Guide7520 Предостережение: Если шлюзовая установка инсталлируется в помещении, позаботьтесь, чтобы в помещении не было пы

Appendix C: Translated Electrical, Safety, and Emission Information7630 Внимание: Корпус может быть тяжелым и поднять его может быть сложно. Allied Te

AT-FS20x Series Installation Guide77Телекоммуникационное соответствие41 Внимание: При использовании телефонного оборудования, всегда следует обращать

AT-FS20x Series Installation GuideixWhere to Find Web-based GuidesThe installation and user guides for all Allied Telesyn products are available in po