Allied-telesis AT-CV1KSS Converteon Line Card User Manual
Browse online or download User Manual for Computer hardware Allied-telesis AT-CV1KSS Converteon Line Card. Allied Telesis AT-CV1KSS Converteon Line Card User Manual
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1 2 3
613-000297 Rev. D
AT-CV1KSS Converteon Line Card Installation Guide
Overview
The AT-CV1KSS line card is a dual 1000Base-TX SFP line card. You can install this line
card in any Converteon Series chassis. The line card features two small form factor
pluggable (SFP) transceiver slots. The line card is hot-swappable into and out of a
Converteon chassis.
Related Documents
For details on the features and functions of a Converteon chassis, refer to the relevant
documents on our web site, www.alliedtelesis.com.
Verifying Package Contents
Ensure that the following items are included in your package:
One AT-CV1KSS line card
This installation guide
If any item is missing or damaged, contact your Allied Telesis sales representative for
assistance.
AT-CV1KSS Line Card Components
An AT-CV1KSS line card has the components shown below.
SFP Ports Description
The SFP ports support an SFP transceiver with a fixed operating speed of 1000 Mbps.
LEDs
The AT-CV1KSS line card has three status LEDs and two LEDs for each SFP port, as
described in “LED Descriptions.”
DIP Switches
One set of DIP switches allows you to set the operating mode, as described in “DIP Switch
Settings.”
Installing an AT-CV1KSS Line Card
Note
Before you install an AT-CV1KSS line card, refer to the appropriate Converteon
chassis installation guide for electrical safety and emissions information.
Note
You can install a Converteon line card in any Converteon chassis line card slot.
To install an AT-CV1KSS line card, perform the following procedure:
1. Remove the AT-CV1KSS line card from its shipping package and store the package
in a safe place. You must use the original package if you need to return the unit to
Allied Telesis.
2. Configure the line card’s DIP switches as required. Refer to “DIP Switch Settings” for
more information.
3. Select any line card slot in the chassis where you want to install the AT-CV1KSS line
card, and remove the blank slot cover if one is installed.
4. Align the back edge of the line card with the to and bottom alignment guides located
inside the slot.
5. Slide the line card into the slot until the front of the card is flush with the front of the
chassis.
Note
Avoid touching the line card components.
6. Secure the AT-CV1KSS line card to the chassis by using a Phillips screwdriver to
tighten the captive screw on the faceplate.
Note
Always tighten the captive screw to secure the line card to the chassis.
7. Repeat this procedure to install additional AT-CV1KSS line cards.
LED Descriptions
Status LEDs
The line card has four status LEDs as described in the following table. For more information
about Smart MissingLink and MissingLink, refer to the relevant management software
user’s guide.
SFP Port LEDs
Each SFP port has two LEDs, as described in the following table. For more information
about Smart MissingLink, refer to the relevant management software user’s guide.
DIP Switch Settings
The DIP switches described in the following table allow you to set the operating mode of
the line card. For information about the operating modes as well as Smart MissingLink
and MissingLink, refer to the relevant management software user’s guide.
“X” means that the DIP switch position can be ON or OFF.
Warranty Information
The AT-CV1KSS line card has a limited warranty of five years. Go to
www.alliedtelesis.com/warranty for the specific terms and conditions of the warranty and
for warranty registration.
*613-000297 Rev D*
559
AT-CV1KS
S
LK
A
T
LK A
T
SML ML
R
D
Y
S
F
P
S
F
P
SW
1
ON
1 2 3 4
4 3 2 1
DIP Switches
SFP Ports
Line Card Status LEDs
SFP Port LEDs
Warning: Remove all metal jewelry, such as rings and watches, before installing
or removing a line card from a powered-on chassis.
Caution: Be sure to observe all standard electrostatic (ESD) precautions, such as
wearing an antistatic wrist strap, to avoid damaging the device. A line card can be
damaged by static electricity
LED State Description
RDY Green The line card has passed diagnostics.
Off The line card has not passed diagnostics.
SML Green The Smart MissingLink mode is enabled.
Off The Smart MissingLink mode is disabled.
ML Green The MissingLink mode is enabled.
Off The MissingLink mode is disabled.
LED State Description
LK Green A link has been established on the port.
Blinking
Green
While in Smart MissingLink mode, a valid connection is established
on the port while a link on the other port is lost.
Off No link has been established on the port.
AT Blinking
Green
TX/RX activity has been detected on the port.
Off There is no TX/RX activity on the port.
Operating Mode DIP 1 DIP 2 DIP 3 DIP 4
Smart MissingLink (SML) OFF ON ON X
MissingLink (ML) OFF OFF ON X
Link Test (default) OFF OFF OFF X
Manufacturing Defaults OFF OFF OFF X
1
2
Summary of Contents
Page 1 - *613-000297 Rev D*
1 2 3613-000297 Rev. DAT-CV1KSS Converteon Line Card Installation GuideOverviewThe AT-CV1KSS line card is a dual 1000Base-TX SFP line card. You can in
Page 2 - Specifications
4 5 6SpecificationsDimensions (H x W x L) 2.2 cm x 7.3 cm x 13.0 cm(.78 in. x 2.89 in. x 5.1 in.)Weight 0.27 kg (0.60 lbs.)Operating Temperature 0° C
Related products and manuals for Computer hardware Allied-telesis AT-CV1KSS Converteon Line Card
(128 pages)© 2020, manymanuals.com. All rights reserved. | 2.200 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals