613-000731 Rev AEnclosure and Intelligent Multiservice Gateways _________________AT-EN646MOD EnclosureInstallation Guide
AT-EN646MOD Installation Guide10 Chapter 3: Enclosure InstallationCheck Package ContentsThe following items are included in the enclosure package. If
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 11Mount the EnclosureTo mount the AT-EN646MOD enclosure, perform the following procedu
AT-EN646MOD Installation Guide12 Chapter 3: Enclosure InstallationInstall the Grounding Plate1. Remove the grounding plate and the self-tapping screws
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 13Figure 6. Aligning the Ground Plate
AT-EN646MOD Installation Guide14 Chapter 3: Enclosure InstallationInstall the Fiber Clips onto the Grounding Plate1. From the accessory kit, take out
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 15Option 1 - Install the Dielectric Drop CableSecuring the Fiber Optic Drop CableTo in
AT-EN646MOD Installation Guide16 Chapter 3: Enclosure InstallationFigure 9. Positioning the Cable11. Tighten the Kepnuts on the strength member clamp
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 1712. Replace the bar, washers, and Kepnuts on the posts of the drop cable clamp and t
AT-EN646MOD Installation Guide18 Chapter 3: Enclosure InstallationInstall the Ground WireThe AT-iMG646MOD must be connected to a good earth ground.Cau
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 19Secure the Entrance (Replace/Seal the Grommet and Install Tie-Down)1. Take the gromm
Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied
AT-EN646MOD Installation Guide20 Chapter 3: Enclosure InstallationSecure the Tracer Wire and Aramid YarnNoteAny tracer wire or cable armoring on the f
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 21Option 2 - Install the Armored Drop CableTo install the fiber optic drop cable, perf
AT-EN646MOD Installation Guide22 Chapter 3: Enclosure InstallationNoteMake sure that the fiber optic cable is not secured by either clamp.10. Position
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 23Install the Ground WireThe AT-iMG646MOD must be connected to a good earth ground.Cau
AT-EN646MOD Installation Guide24 Chapter 3: Enclosure InstallationSecure the Entrance (Replace/Seal the Grommet and Install Tie-Down)1. Take the gromm
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 25Splice the Drop Cable and Securing the Fusion Splice Tray1. Locate the fusion splice
AT-EN646MOD Installation Guide26 Chapter 3: Enclosure Installation8. Route the buffer tube from the drop cable to the upper left corner of the splice
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 2712. Strip the SC/UPC pigtail jacket to expose 22.75 in. (58 cm) of fiber.13. Clean t
AT-EN646MOD Installation Guide28 Chapter 3: Enclosure InstallationFigure 24. Splicing Tray - CompleteNoteThe AT-iMG646MOD WAN module has a receive sen
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 29Secure the Optical WireNoteIt is critical that you maintain a minimum fiber bend rad
3Chapter 1: Preface ...
Figure 26. Enclosure Connections at End of Installation
AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 31
AT-EN646MOD Installation Guide32 Chapter 3: Enclosure Installation613-000731 A
Contents4
AT-EN646MOD Installation Guide5Chapter 1PrefaceThis guide contains instructions on how to install the AT-EN646MOD enclosure. This guide is used when t
Preface6web site: www.alliedtelesis.com.Returning Products Products for return or repair must first be assigned a return materials authorization (RMA)
AT-EN646MOD Installation GuideEnclosure Overview 7Chapter 2Enclosure OverviewFeaturesThe AT-EN646MOD enclosure houses and protects the AT-iMG646MOD se
8 Enclosure OverviewThe AT-EN646MOD Interfaces to the NetworkThe AT-EN646MOD allows the AT-iMG646MOD to be installed in an outdoor environment. Refer
9Chapter 3Enclosure InstallationTools RequiredHave the following tools on hand before you install the enclosure: 3/8” drill Drill bit for the size o
Comments to this Manuals