Allied Telesis AT-FS201ST/FS3 Installation Guide

AT-MC104XLAT-MC104LHAT-MC104SC/FS3, FS4AT-MC104ST/FS3, FS4Version 3 Fast Ethernet Media ConvertersInstallation GuidePN 613-10781-00 Rev D

xFor Sales or Corporate InformationTell Us What You ThinkIf you have comments or suggestions to improve this or other Allied Telesyn documents, please

1AT-MC104 Series Fast Ethernet Media ConvertersThe AT-MC104 Series Media Converters include the following models:AT-MC104 Series Fast Ethernet Media C

2Table 1 list the maximum cabling distances for each model.Table 1 Maximum Operating DistancesKey FeaturesThe media converters have the following key

AT-MC104 Series Installation Guide3Status LEDsTable 2 defines the system LEDs.Table 2 Status LEDs Link Test/MissingLink ButtonThe Link Test/MissingLi

4MissingLink. The MissingLink feature activates the fiber optic ports on the media converter to pass the “Link” status of their connections to each ot

AT-MC104 Series Installation Guide5Network TopologiesFigure 3 shows two typical network configurations of the media converter.Figure 3 Typical Config

6Installing the Media ConverterThe following sections explain how to install the media converter. The media converter can be installed either as a sta

AT-MC104 Series Installation Guide7Cable SpecificationsTable 3, Table 4, and Table 5 list the IEEE 802.3u cabling specifications for the AT-MC104 Seri

8Table 5 Single-mode Port Specifications (Half-duplex)11. The total distance of the fiber optic lengths cannot exceed the limits stated in the table.

AT-MC104 Series Installation Guide9Verifying the Package ContentsMake sure the following items are included in your media converter package. If any of

Copyright  2000 Allied Telesyn International, Corp.960 Stewart Drive Suite B, Sunnyvale CA 94086 USAAll rights reserved. No part of this publication

10Installing the Media ConverterThe following procedure explains how to install the media converter.If you are building a back-to-back installation, p

AT-MC104 Series Installation Guide117. Remove the dust covers from the fiber optic connectors.8. Connect the fiber optic cables to their respective po

124. Check the two LNK LEDs. They should be green, indicating that the media converter is receiving a signal from the nodes connected to the ports. If

AT-MC104 Series Installation Guide13Warranty RegistrationWhen you finish the installation, register your product by completing the enclosed warranty c

14Single-mode Port SpecificationsTable 6 Fiber Optic TransmitterTable 7 Fiber Optic ReceiverModelFiber Type11. SMF = Single-mode FiberFiber Optic Di

AT-MC104 Series Installation Guide15Table 8 Fiber Optic DatalinkTable 9 Fiber Optic Loss Specifications (Benchmarks)ModelFiber Optic Diameter (micro

16Multimode Port Specifications (All Models)Table 10 Fiber Optic TransmitterTable 11 Fiber Optic ReceiverTable 12 Fiber Optic DatalinkFiber Type11.

AT-MC104 Series Installation Guide17Table 13 Fiber Optic Loss Specifications (Benchmarks)Fiber Type1Fiber Optic Diameter (microns)Optical FrequencyTy

19Appendix ATranslated Safety StatementsImportant: This appendix contains multiple-language translations for the safety statements in this guide.Wicht

iiiSafety WarningsStandards: This product meets the following standards.RFI EmissionEN55022 Class B ! 1ImmunityEN50082-1 1997 ! 2Electrical SafetyTUV-

20Standards: This product meets the following standards.! 1RFI Emission EN55022 Class B! 2Immunity EN50082-1 1997! 3Electrical Safety EN60950, UL1950,

AT-MC104 Series Installation Guide21At time of installation, the Fiber Optic Lasers comply with FDA Radiation Performance Standard 21CFR Subchapter J,

22!10 BETRIEBSTEMPERATURDieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 40° C entworfen.!11 ALLE LÄNDER: Installa

AT-MC104 Series Installation Guide23!7 GEVAAR VOOR BLIKSEMINSLAGGEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.!8VENTILATIEGATEN NIET BLOKKE

24Standardit: Tämä tuote on seuraavien standardien mukainen.!1Radioaaltojen häirintä EN55022 Luokka B!2Kestävyys EN50082-1 1997!3Sähköturvallisuus TU

AT-MC104 Series Installation Guide25!9Questo dispositivo deve essere alimentato solo mediante l’adattatore.EUROPE - EUUtilizzare l’adattatore per c.a.

26Padrões: Este produto atende aos seguintes padrões.!1Emissão De Interferência De Radiofrequência EN55022 Classe B!2Imunidade EN50082-1 1997!3Segura

AT-MC104 Series Installation Guide27!9La energía para el dispositivo central o "hub" debe provenir únicamente del adaptador.EUROPE - EUUtili

29Appendix BAT-MC104 Series Installation Guide FeedbackPlease tell us what additional information you would like to see discussed in this guide. If th

ivEUROPE - EUUse TÜV licensed AC adapter of DC 12V, 500mA.UKUse a UK Safety Approved AC adapter of DC 12V, minimum 500mA.Important: Appendix A contain

31Appendix CTechnical Support Fax OrderName _________________________________________________________________Company__________________________________

vTable of ContentsSafety Warnings ... iiiWelcome to Allied Te

viAppendix ATranslated Safety Statements ... 19Appendix BAT-MC104 Series Installation

viiThis guide contains instructions on how to install an AT-MC104 Series Fast Ethernet Media Converter.Where to Find Web-based GuidesThe Allied Telesy

viiiContacting Allied Telesyn Technical SupportThere are several ways to contact Allied Telesyn technical support: online, telephone, fax or e-mail.On

AT-MC104 Series Installation GuideixReturning ProductsProducts for return or repair must first be assigned a Return Materials Authorization (RMA) numb