Allied Telesis AT-CV10x Series User Manual download pdf

1 2 3

613-000296 Rev. D

AT-CV10x Series Converteon Line Cards

Installation Guide

Overview

The AT-CV10x Series (AT-CV101, AT-CV102, and AT-CV102/x Series) line cards feature

a 10Base-TX twisted pair port and a 100Base-FX fiber optic port. You can install these

line cards in any Converteon Series chassis. The line card features one fiber optic port

and one copper twisted pair port. Both ports feature half- or full-duplex mode operation.

The line cards are hot-swappable into and out of a Converteon chassis.

Related Documents

For details on the features and functions of a Converteon chassis, refer to the relevant

documents on our web site, www.alliedtelesis.com.

Verifying Package Contents

Ensure that the following items are included in your package:

 One AT-CV10x Series line card

 This installation guide

If any item is missing or damaged, contact your Allied Telesis sales representative for

assistance.

AT-CV10x Series Line Card Components

An AT-CV10x Series line card has the components shown below. The AT-CV102 line card

is shown as an example.

Port Descriptions

Fiber Optic Port

The fiber optic port on the AT-CV10x Series line card is IEEE 802.3ah-compliant. The

connectors and operating distance vary depending upon the model:

 AT-CV101: multi-mode fiber ST connector and a maximum operating distance of 2km

(1.24 miles)

 AT-CV102: multi-mode fiber SC connector and a maximum operating distance of 2km

(1.24 miles)

 AT-CV102/1: single mode fiber SC connector with a maximum operating distance of

15km (9.32 miles)

 AT-CV102/2: single mode fiber SC connector with a maximum operating distance of

40km (24.85 miles)

Twisted Pair Port

The 10/100Base-TX compliant twisted pair port has an RJ-45 connector and a maximum

operating distance of 100 meters (328 feet). Category 5 (5E), 100 Ohm shielded or

unshielded twisted pair cabling is required. The pinouts for this port are shown in

“Twisted Pair Port Pinouts.”

LEDs

An AT-CV10x Series line card as three status LEDs, two LEDS for the fiber optic port, and

three LEDs for the twisted pair port, as described in “LED Descriptions.”

DIP Switches

Two sets of DIP switches allow you to set the operating mode and MDI/MDI-X features, as

described in “DIP Switch Settings.”

Installing an AT-CV10x Series Line Card

Note

Before you install an AT-CV10x Series line card, refer to the appropriate Converteon

chassis installation guide for electrical safety and emissions information.

Note

You can install a Converteon line card in any Converteon chassis line card slot.

To install an AT-CV10x Series line card, perform the following procedure:

1. Remove the AT-CV10x Series line card from its shipping package and store the

package in a safe place. You must use the original package if you need to return the

unit to Allied Telesis.

2. Configure the line card’s DIP switches as required. Refer to “DIP Switch Settings” for

more information.

3. Select any line card slot in the chassis where you want to install the AT-CV10x

Series line card, and remove the blank slot cover if one is installed.

4. Align the back edge of the line card with the to and bottom alignment guides located

inside the slot.

5. Slide the line card into the slot until the front of the card is flush with the front of the

chassis.

Note

Avoid touching the line card components.

6. Secure the AT-CV10x Series line card to the chassis by using a Phillips screwdriver

to tighten the captive screw on the faceplate.

Note

Always tighten the captive screw to secure the line card to the chassis.

7. Repeat this procedure to install additional AT-CV10x Series line cards.

LED Descriptions

Status LEDs

The line card has three status LEDs as described in the following table. For more

information about Smart MissingLink and MissingLink, refer to the relevant management

software user’s guide.

Fiber Optic Port LEDs

The fiber optic port has two LEDs, as described in the following table. For more

information about Smart MissingLink, refer to the relevant management software user’s

guide.

Twisted Pair Port LEDs

The twisted pair port has three LEDs, as described in the following table. For more

information about Smart MissingLink, refer to the relevant management software user’s

guide.

*613-000296 Rev D*

555

1 2 3 4

AT-CV10 2

RDY

1 2 3 4

SW1

SW1 DIP Switch Set

SW2 DIP Switch Set

Fiber Optic Port LEDs

Fiber Optic Port

Twisted Pair Port LEDs

Line Card Status LEDs

10/100-TX Twisted Pair Port

Warning: Remove all metal jewelry, such as rings and watches, before installing

or removing a line card from a powered-on chassis.

Caution: Be sure to observe all standard electrostatic (ESD) precautions, such as

wearing an antistatic wrist strap, to avoid damaging the device. A line card can be

damaged by static electricity

LED State Description

RDY Green The line card has passed diagnostics.

Off The line card has not passed diagnostics.

SML Green The Smart MissingLink mode is enabled.

Off The Smart MissingLink mode is disabled.

ML Green The MissingLink mode is enabled.

Off The MissingLink mode is disabled.

LED State Description

LK Green A link has been established on the port.

Blinking

Green

While in Smart MissingLink mode, a valid connection is established

on the port while a link on the other port is lost.

Off No link has been established on the port.

AT Blinking

Green

TX/RX activity has been detected on the port.

Off There is no TX/RX activity on the port.

LED State Description

LK Green A link has been established on the port.

Blinking

Green

While in Smart MissingLink mode, a valid connection is established

on the port while a link on the other port is lost.

Off No link has been established on the port.

AT Blinking

Green

TX/RX activity has been detected on the port.

Off There is no TX/RX activity on the port.

FD Green (AT-CV102 only) The port is operating in full-duplex mode.

Off The port is operating in half-duplex mode.

1 2

Summary of Contents

Page 1 - *613-000296 Rev D*

1 2 3613-000296 Rev. DAT-CV10x Series Converteon Line CardsInstallation GuideOverviewThe AT-CV10x Series (AT-CV101, AT-CV102, and AT-CV102/x Series) l

Page 2 - Specifications

4 5 6DIP Switch SettingsSW 1 DIP SwitchesThe DIP switches in the SW 1 DIP switch set described in the following table allow you to set the operating m

Comments to this Manuals

No comments

Allied Telesis AT-CV10x Series User Manual

Browse online or download User Manual for Network switches Allied Telesis AT-CV10x Series. AT-CV10x Series Media Converter Line Cards

Summary of Contents

Comments to this Manuals

Related products and manuals for Network switches Allied Telesis AT-CV10x Series