Allied Telesis Switch AT-9000/12POE User Manual

613-001876 Rev. AAT-9000 SeriesGigabit Ethernet Switches AT-9000/12PoE AT-9000/28 AT-9000/28PoE AT-9000/28SP AT-9000/52Installation Guide

Tables10

11PrefaceThis manual is the installation guide for the AT-9000 Gigabit Ethernet Switches. The switch models included in this series are: AT-9000/12PO

AT-9000 Gigabit Ethernet Switch Installation Guide12Document ConventionsThis document uses the following conventions:NoteNotes provide additional info

Preface13Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support

AT-9000 Gigabit Ethernet Switch Installation Guide14

15Chapter 1OverviewThis chapter contains the following sections: “Switch Models and Features” on page 16 “AT-9000 Series Gigabit Ethernet Switches”

AT-9000 Gigabit Ethernet Switch Installation Guide16Switch Models and FeaturesAT-9000 SeriesModelsThe AT-9000 series offers the following models: AT-

Chapter 1: Overview17Power overEthernetHere are the basic features of Power over Ethernet (PoE): PoE and PoE+ supported on the 10/100/1000Base-TX por

AT-9000 Gigabit Ethernet Switch Installation Guide18Port LEDs Here are the port LEDs: Duplex mode and link/activity LEDs for the twisted-pair ports

Chapter 1: Overview19AT-9000 Series Gigabit Ethernet SwitchesAll of the AT-9000 Managed Layer 2 Gigabit Ethernet Switches include the following featur

Copyright © 2013 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

AT-9000 Gigabit Ethernet Switch Installation Guide20Figure 2. AT-9000/12POE Switch Front and Rear Panels10/100/1000Base-T PortsSFPPortsConsolePortecoF

Chapter 1: Overview21AT-9000/28SwitchFeatures specific to the AT-9000/28 switch include: 28 port Gigabit Switch with 24 10/100/1000Base-T RJ-45 ports

AT-9000 Gigabit Ethernet Switch Installation Guide22AT-9000/28POESwitchFeatures specific to the AT-9000/28POE switch include: 28 port Gigabit Switch

Chapter 1: Overview23AT-9000/28SPSwitchFeatures specific to the AT-9000/28SP switch include: 28 port Gigabit Switch with 24 Gigabit Ethernet small fo

AT-9000 Gigabit Ethernet Switch Installation Guide24AT-9000/52SwitchFeatures specific to the AT-9000/52 switch include: 52 port Gigabit Switch with 4

Chapter 1: Overview2510/100/1000Base-T Twisted-Pair PortsA twisted-pair cable port is shown in Figure 7.Figure 7. Twisted-Pair Cable PortSee Figure 19

AT-9000 Gigabit Ethernet Switch Installation Guide26NoteA switch port connected to a host device that does not support Autonegotiation, and has a fixe

Chapter 1: Overview27Port Pinouts Refer to Table 15 on page 84, Table 17 on page 85, and Table 17 on page 85 for the port pinouts of the 10/100/1000Ba

AT-9000 Gigabit Ethernet Switch Installation Guide28Power Over EthernetThe AT-9000/12POE and AT-9000/28POE switches feature Power over Ethernet (PoE)

Chapter 1: Overview29Powered DeviceClassesPowered devices are grouped into the five classes listed in Table 2. The classes are based on the amount of

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN61000

AT-9000 Gigabit Ethernet Switch Installation Guide30The switch can handle different power requirements on different ports. This enables you to connect

Chapter 1: Overview31WiringImplementationThe IEEE 802.3af standard defines two methods by which a PSE, such as the switch, can transmit DC power over

AT-9000 Gigabit Ethernet Switch Installation Guide32SFP SlotsThe AT-9000/12POE, AT-9000/28, AT-9000/28POE, and AT-9000/28SP switches have four slots f

Chapter 1: Overview33 Port speed is an exception to the shared settings of the twisted-pair port and SFP slot of a combo port. If you disable Autoneg

AT-9000 Gigabit Ethernet Switch Installation Guide34Combo PortsThe AT-9000/28, AT-9000/28POE, and AT-9000/28SP switches have four combo pairs of uplin

Chapter 1: Overview35NoteFor a list of supported SFP transceivers for the AT-9000 Series Managed Layer 2 Gigabit Ethernet Switches, contact your Allie

AT-9000 Gigabit Ethernet Switch Installation Guide36Console PortThe Console port is used to configure the features and parameter settings of the switc

Chapter 1: Overview37LEDs Here are descriptions of the switch LEDs.System LEDs There are two system LEDs, the Power (PWR) LED and System (SYS) LED, as

AT-9000 Gigabit Ethernet Switch Installation Guide38 AT-9000/28, AT-9000/28SP, AT-9000/52: either collision, speed, duplex, or activity, depending on

Chapter 1: Overview39is indicated on one of the LEDs next to the MODE LED SELECT button, as shown in Figure 10.Figure 10. Front Panel MODE LED SELECT

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

AT-9000 Gigabit Ethernet Switch Installation Guide40SFP LEDs Each SFP slot has one SFP LINK/ACT LED. An up-arrow LED corresponds to the upper SFP slot

Chapter 1: Overview41ecoFriendly ButtonThe ecoFriendly button enables the Low Power Mode (LPM) feature. This mode allows you to conserve power by turn

AT-9000 Gigabit Ethernet Switch Installation Guide42Power SuppliesThe AT-9000/12POE, AT-9000/28, AT-9000/28SP, and AT-9000/52 switches have one AC pow

Chapter 1: Overview43Power ConnectorsThe AT-9000/12POE, AT-9000/28, AT-9000/28SP, and AT-9000/52 switches have one AC power supply socket on the back

AT-9000 Gigabit Ethernet Switch Installation Guide44

45Chapter 2Beginning the InstallationThis chapter contains the following sections: “Installation Procedures” on page 46 “Reviewing Safety Precaution

AT-9000 Gigabit Ethernet Switch Installation Guide46Installation ProceduresYou may install the switch on a table or desktop, or in an equipment rack.

Chapter 2: Beginning the Installation47Reviewing Safety PrecautionsReview the following safety precautions before you begin to install the switch or a

AT-9000 Gigabit Ethernet Switch Installation Guide48WarningDo not work on equipment or cables during periods of lightning activity.  E2WarningPower c

Chapter 2: Beginning the Installation49WarningOnly trained and qualified personnel are allowed to install or replace this equipment. E14CautionCircui

5ContentsPreface ...

AT-9000 Gigabit Ethernet Switch Installation Guide50CautionInstallation of the equipment in a rack should be such that the amount of air flow required

Chapter 2: Beginning the Installation51Selecting a SiteObserve the following requirements when choosing a site for the switch: If you plan to install

AT-9000 Gigabit Ethernet Switch Installation Guide52Unpacking the SwitchTo unpack the switch, perform the following procedure:1. Remove all components

53Chapter 3Installing the Switch on a Table or RackThis chapter contains the following sections: “Installing the Switch on a Table or Desktop” on pag

AT-9000 Gigabit Ethernet Switch Installation Guide54Installing the Switch on a Table or DesktopYou may install the switch on a table or desktop. Here

Chapter 3: Installing the Switch on a Table or Rack55Installing the Switch in a RackInstallation guidelines may be found in “Selecting a Site” on page

AT-9000 Gigabit Ethernet Switch Installation Guide56.Figure 14. Attaching Brackets for Rack Mounting.Figure 15. Attaching Brackets for Rack Mounting (

Chapter 3: Installing the Switch on a Table or Rack576. Mount the switch in the 19-inch rack using standard screws (not provided), as shown in Figure

AT-9000 Gigabit Ethernet Switch Installation Guide58

59Chapter 4Cabling the Networking PortsObserve the following guidelines when connecting a twisted-pair cable to a port on the switch: The cable speci

AT-9000 Gigabit Ethernet Switch Installation Guide6Reviewing Safety Precautions ...

AT-9000 Gigabit Ethernet Switch Installation Guide60 The default speed setting for the ports is Autonegotiation. This setting is appropriate for port

61Chapter 5Powering On the SwitchThis chapter contains the following sections: “Applying AC Power” on page 62 “Starting a Local Management Session”

AT-9000 Gigabit Ethernet Switch Installation Guide62Applying AC PowerConsider the following items as you power on the switch: All of the models have

Chapter 5: Powering On the Switch632. Connect the other end of the power cord to an appropriate AC power outlet. For power specifications for the swit

AT-9000 Gigabit Ethernet Switch Installation Guide64Starting a Local Management SessionThe procedure in this section explains how to start a local (ou

Chapter 5: Powering On the Switch654. Press Enter.You are prompted for a user name and password. 5. To configure the switch settings, enter “manager”

AT-9000 Gigabit Ethernet Switch Installation Guide66Management MethodsYou may use the following methods and tools to manage AT-9000 series switches:

Chapter 5: Powering On the Switch67Secure ShellManagementSecure Shell (SSH) management is similar to Telnet management in that you may use it, togethe

AT-9000 Gigabit Ethernet Switch Installation Guide68SNMP Refer to the AT-9000 Series Management Command Line Interface User’s Guide for instructions o

Chapter 5: Powering On the Switch69Adding a Management IP AddressYou must assign the switch a management IP address to access the web user interface a

7FiguresFigure 1. AT-9000/28POE Switch...

AT-9000 Gigabit Ethernet Switch Installation Guide70Table 9. Example of Adding a Management Addressawplus> enable Move to the Privileged Exec mode.

71Chapter 6TroubleshootingThis chapter contains information about how to troubleshoot the switch in the event a problem occurs.NoteIf you are unable t

AT-9000 Gigabit Ethernet Switch Installation Guide72Power LED Is OffCheck the PWR LED on the front of the switch. If the LED is off, indicating that t

Chapter 6: Troubleshooting73Twisted-Pair Port Link LED Is OffWhen a twisted-pair port on the switch is connected to a properly operating end node, the

AT-9000 Gigabit Ethernet Switch Installation Guide74 If a switch port is using Autonegotiation (the default setting) to set its speed and duplex mode

Chapter 6: Troubleshooting75Cannot Establish a Local (Out-of-Band) Management SessionIf you are unable to establish a local (out-of-band) management s

AT-9000 Gigabit Ethernet Switch Installation Guide76All Port LEDs Are OffIf all of the port LEDs are off, even though the ports are connected to activ

Chapter 6: Troubleshooting77Power Over EthernetThis section applies only to the AT-9000/12POE and AT-9000/28POE switches.Each RJ-45 port switch has tw

AT-9000 Gigabit Ethernet Switch Installation Guide78Fiber Optic TransceiversThis section applies only to the AT-9000/12POE, AT-9000/28, AT-9000/28POE,

Chapter 6: Troubleshooting79Slow Performance Between Switch and Host DeviceIf network performance between a twisted-pair port on the switch and a host

Figures8

AT-9000 Gigabit Ethernet Switch Installation Guide80

81Appendix ATechnical SpecificationsAll specifications listed below are identical for all AT-9000 series switches, except for the Physical Specificati

AT-9000 Gigabit Ethernet Switch Installation Guide82Environmental SpecificationsPower SpecificationsAC Power ConsumptionAC Input Electrical RatingsF

Appendix A: Technical Specifications83Safety and Electromagnetic Emissions CertificationsEMIFCC Class A, CISPR 22 Class A, EN55022 Class A, C-TICKImmu

AT-9000 Gigabit Ethernet Switch Installation Guide8410/100/1000Base-T Twisted-Pair Port ConnectorsThis section lists the pin signals for the 10/100/10

Appendix A: Technical Specifications85Table 17 lists the RJ-45 connector pins and their signals when a 1000Base-T port is operating at 1000 Mbps.Conso

AT-9000 Gigabit Ethernet Switch Installation Guide86

9TablesTable 1. Twisted-Pair Cable for the 10/100/1000Base-T Ports .....................