Allied Telesis AT-MC606 User Manual

613-001383 Rev. AVDSL Ethernet Extender over CoaxAT-MC606 Installation Guide

Tables10

11PrefaceThis guide contains instructions on how to install the AT-MC606 VDSL Network Extender and contains the following sections: “Safety Symbols U

Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-MC606 VDSL Network Extender Installation Guide13Where to Find Web-based GuidesThe product documentation for all Allied Telesis products are availab

Preface14Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate infor

15Chapter 1OverviewThe AT-MC606 VDSL Network Extender product is designed to extend Ethernet traffic using VDSL technology over coaxial cable.This cha

Overview16Summary of FeaturesThe AT-MC606 VDSL Network Extender using coaxial cable provides the following features: Extend Ethernet over shielded co

AT-MC606 VDSL Network Extender Installation Guide17Figure 2. illustrates the rear panels of the AT-MC606 VDSL Network Extender.Figure 2. AT-MC606 Rear

Overview18AT-MC606 Port DescriptionsVDSL Line Port The VDSL Line port features a BNC coaxial connector. It allows you to connect two AT-MC606 VDSL Net

AT-MC606 VDSL Network Extender Installation Guide19the Ethernet port is set to 100 Mbps.Half- and Full-duplex ModeDuplex mode refers to the way an end

Copyright © 2010 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Overview20RJ-45 Port PinoutsThe pin assignments of an RJ-45 10Base-T/100Base-TX connector and port are illustrated in Figure 3.Figure 3. RJ-45 10Base-

AT-MC606 VDSL Network Extender Installation Guide21Status LEDsThe AT-MC606 VDSL Network Extender features the status LEDs and are defined in Table 3.T

Overview22VDSL Configuration DIP SwitchesVDSL SwitchDefinitionsThe AT-MC606 VDSL Network Extender features the four VDSL Configuration DIP switches on

AT-MC606 VDSL Network Extender Installation Guide23The front panel VDSL Configuration DIP switches are shown in Figure 4Figure 4. VDSL Configuration D

Overview24ASYM/SYM VDSL Configuration SwitchThe ASYM/SYM (Right Center) switch selects the maximum data rate for the VDSL line. The ASYM (asymmetrical

AT-MC606 VDSL Network Extender Installation Guide25External AC/DC Power AdapterAn external, energy efficient, AC/DC power adapter is included with the

Overview26Applications for the AT-MC606 VDSL Network ExtenderThe AT-MC606 VDSL Network Extender is designed to be used in pairs to extend Ethernet tra

AT-MC606 VDSL Network Extender Installation Guide27for Asymmetrical data mode to maximize the amount of data being sent to the Subscriber and minimize

29Chapter 2InstallationThis chapter contains the installation procedures for the AT-MC606 VDSL Network Extender in the following sections: “Reviewing

Overview30Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the switch or any of its components.

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class B, EN55022 Class B, EN61000-3-2, EN61000-

AT-MC606 VDSL Network Extender Installation Guide31Selecting a Site for the AT-MC606 VDSL Network ExtenderObserve the following requirements when choo

Overview32Required CablingThe AT-MC606 VDSL Network Extender requires two or more of the three cables described in Table 5 below. These cables are not

AT-MC606 VDSL Network Extender Installation Guide33Unpacking the AT-MC606 VDSL Network ExtenderTo unpack the AT-MC606 product:1. Remove all components

Overview34Installing the AT-MC606 VDSL Network Extender Subscriber UnitThe AT-MC606 Subscriber unit is normally used as a stand-alone device, or can b

AT-MC606 VDSL Network Extender Installation Guide355. Go to “Cabling the Subscriber Unit” on page 35 to connect the cables and to “Powering On the Sub

Overview362. Connect a coaxial cable from the VDSL Line port to the wall/interior coaxial cable, as shown in Figure 10, so that the Subscriber unit ca

AT-MC606 VDSL Network Extender Installation Guide37Powering On theSubscriber UnitPower on the Subscriber unit using the power adapter provided, as sho

Overview38Installing the AT-MC606 VDSL Network Extender Provider UnitThe AT-MC606 Provider unit can either be installed in an AT-MCR12 rackmount chass

AT-MC606 VDSL Network Extender Installation Guide393. Configure the right VDSL CONFIG switch (SCBR/PROV) to the SCBR position as shown in Figure 13.Fi

Overview40Rack-Mountingthe Provider UnitTo install the Provider unit in an AT-MCR12 rackmount chassis, perform the following steps:1. Configure the ri

4Translated Safety StatementsImportant: The  symbol indicates that a translation of the safety statement is available in a PDF document titled “Trans

AT-MC606 VDSL Network Extender Installation Guide41Cabling theProvider UnitTo cable the Provider unit, perform the following steps:1. Connect the Ethe

42Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the AT-MC606 VDSL Network Extender in the event a problem occurs.No

AT-MC606 VDSL Network Extender Installation Guide43LINK/ACT LED - 10Base-T/100BaseTX Ethernet PortVerify that the LINK/ACT LED for the 10Base-T/100Bas

44Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: (W x D x H)109 mm x 95 mm x 25 mm(4.29 in. x 3.74 in. x 0.98 in.)Weight: .3 kg

AT-MC606 VDSL Network Extender Installation Guide45Safety and Electromagnetic Compatibility CertificationsEmission: EN55022 Class B, FCC Part 15 Class

5Preface ...

Contents6

7List of FiguresFigure 1. AT-MC606 Front Panel...

Figures8

9Table 1. Safety Symbols ..............................