Allied Telesis x600-24Ts Installation Guide

613-001065 Rev. Bx600 Series Layer 3 Gigabit Ethernet Switchesx600-24Tsx600-24Ts/XPx600-48Tsx600-48Ts/XP◆Installation Guide

Preface10Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

x600 Layer 3 Gigabit Ethernet Switch Installation Guide11Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis product

Preface12Contacting Allied TelesisThis section provides Allied Telesis contact information for technical support as well as sales and corporate inform

13Chapter 1 OverviewThis chapter contains the following sections: “Introduction” on page 14 “Switch Descriptions” on page 15 “10/100/1000Base-T Twi

Chapter 1: Overview14IntroductionThe x600 Series Switches are managed Gigabit Ethernet switches that acts as standalone units. There are four Basic La

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide15Switch DescriptionsThe following sections describe the x600-24Ts, x600-24Ts/XP, x600

Chapter 1: Overview16x600-24Ts/XPSwitchThe x600-24Ts/XP switch has the following hardware features: 24 10/100/1000Base-T ports Four Gigabit Ethernet

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide17x600-48Ts Switch The x600-48Ts switch has the following hardware features: 44 10/10

Chapter 1: Overview18x600-48Ts/XPSwitchThe x600-48Ts/XP switch has the following hardware features: 44 10/100/1000Base-T ports Four Gigabit Ethernet

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide1910/100/1000Base-T Twisted Pair PortsThis section describes the twisted pair ports on

Copyright © 2008 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Overview20Cable Type The cabling requirements for a 10/100/1000Base-T port are: For 10 Mbps operation: Standard TIA/EIA 568-B-compliant Ca

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide21SFP Transceiver SlotsAll of the x600 Series switches feature slots for four optional

Chapter 1: Overview22XFP Transceiver SlotsThe x600-24Ts/XP and the x600-48Ts/XP Switches have two slots for optional XFP 10 Gigabit Ethernet transceiv

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide23Redundant Twisted Pair PortsFour of the twisted pair ports on the x600-24-Ts and x60

Chapter 1: Overview24SD Card SlotAll of the x600 Series Switches have an SD card slot which is designed for an SD card which stores configuration file

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide25Port LEDsThe following sections describe the twisted pair port, SFP, and XFP LEDs. S

Chapter 1: Overview26SFP LEDs Each SFP transceiver slot on the x600 switches has one LED, defined in Table 4.XFP TransceiverSlot LEDsEach 10 Gigabit E

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide27System LEDsThe system LEDs on the front panel display general status information. Se

Chapter 1: Overview28Stack LEDsThe STACK LEDs reflect the status of the two Stack ports on the AT-StackXG Stacking Module. These LEDs remain off if th

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide29Secure Digital LEDsBoth the x600-24Ts/XP and x600-48Ts/XP switches have one Secure D

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-

Chapter 1: Overview30Terminal PortThe terminal port is used to establish a local (out-of-band) management session with the switch. You establish a loc

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide31AT-RPS3204 Redundant Power SupplyThe RPS connector on the back panel of the switch c

Chapter 1: Overview32AT-LBM ModuleThe AT-LBM (Link Back) Module is installed in the expansion slot of the x600-48Ts/XP switch. For an illustration, se

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide33AC Power ConnectorThe x600 switches have a single AC power supply socket on the back

Chapter 1: Overview34

35Chapter 2Installing the HardwareThis chapter provides procedures to install an x600 switch. The chapter contains the following sections: “Reviewing

Chapter 2: Installing the Hardware36Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the switche

x600 Layer 3 Gigabit Ethernet Switch Installation Guide37All Countries: Install product in accordance with local and National Electrical Codes.  E8Ci

Chapter 2: Installing the Hardware38Unpacking a SwitchTo unpack a switch, perform the following procedure:1. Remove all components from the shipping p

x600 Layer 3 Gigabit Ethernet Switch Installation Guide39Installing the Power Cord Retaining ClipPerform the following procedure to install the power

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available at www.alliedtelesis.com in a document

Chapter 2: Installing the Hardware40Installing the Switches in an Equipment RackPerform the following procedure to install each switch in a standard 1

x600 Layer 3 Gigabit Ethernet Switch Installation Guide41Figure 19. Attaching Rack-Mount Brackets5. Install the second rack-mount bracket on the other

Chapter 2: Installing the Hardware42Resetting the SwitchYou may need to reset the switch after upgrading the firmware or after you have made a configu

43Chapter 3Cabling the Network PortsThis chapter contains the instructions for attaching network cables to an x600 switch. The chapter contains the fo

Chapter 3: Cabling the Network Ports44Twisted Pair and Fiber Optic Cable SpecificationsTwisted PairCableSpecificationsTable 9 lists the cabling specif

x600 Layer 3 Gigabit Ethernet Switch Installation Guide45OptionalTransceiverCableSpecificationsThe cable specifications for an optional SFP or XFP tra

Chapter 3: Cabling the Network Ports46Installing Optional TransceiversReview the following guidelines before installing an optional SFP or XFP transce

x600 Layer 3 Gigabit Ethernet Switch Installation Guide473. Position the transceiver with the label facing up.4. Slide the transceiver into the slot u

Chapter 3: Cabling the Network Ports486. For the x600-48Ts and x600-48Ts/XP switches, verify that handles on the top two SFPs are in the up position a

x600 Layer 3 Gigabit Ethernet Switch Installation Guide49Installing an XFPTransceiverTo install an XFP transceiver in an x600 switch, perform the foll

5ContentsPreface ...

Chapter 3: Cabling the Network Ports505. Repeat this procedure to install a second XFP transceiver or go to “Cabling the Twisted Pair and Fiber Optic

x600 Layer 3 Gigabit Ethernet Switch Installation Guide51Cabling the Twisted Pair and Fiber Optic PortsObserve the following guidelines when connectin

Chapter 3: Cabling the Network Ports52Powering on a SwitchTo power on a switch, perform the following procedure:1. Position the power cord retaining c

x600 Layer 3 Gigabit Ethernet Switch Installation Guide534. Start a local management session on the unit by performing the next procedure.Starting a L

Chapter 3: Cabling the Network Ports54Warranty RegistrationFor warranty information, go to the Allied Telesis web site at www.alliedtelesis.com.

55Chapter 4TroubleshootingThis chapter contains information about how to troubleshoot a switch in the event a problem occurs. Sections in the chapter

Chapter 4: Troubleshooting56Power LED is OffCheck the PWR LED on the front of the switch. If the LED is off, indicating that the unit is not receiving

x600 Layer 3 Gigabit Ethernet Switch Installation Guide57Twisted Pair Port Link LED is OffWhen a twisted pair port on the switch is connected to a pro

Chapter 4: Troubleshooting58SFP or XFP LED is OffWhen a fiber optic port on the switch is connected to a properly operating end node, the Link LED for

x600 Layer 3 Gigabit Ethernet Switch Installation Guide59Transceiver is Installed but the Status is “Not Present”If a SFP or XFP transceiver is instal

Contents6Chapter 2: Installing the Hardware ...

Chapter 4: Troubleshooting60System Fault LED is BlinkingA blinking FAULT LED indicates that the switch is updating the active boot configuration file.

x600 Layer 3 Gigabit Ethernet Switch Installation Guide61System Fault LED is Steadily OnIf the system FAULT LED is steadily on, a problem has occurred

Chapter 4: Troubleshooting62Cannot Establish a Local (Out-of-Band) Management SessionIf you are unable to establish a local (out-of-band) management s

x600 Layer 3 Gigabit Ethernet Switch Installation Guide63Switch Functions IntermittentlyIf a switch functions intermittently, check the system hardwar

Chapter 4: Troubleshooting64

65Appendix ATechnical SpecificationsPhysical SpecificationsDimensions (H x W x D):x600-24Ts 44 mm x 440 mm x 305 mm(1.72 in. x 17.34 in. x 12.0 in.)x6

Appendix A: Technical Specifications66Power SpecificationsMaximum Power Consumption:x600-24Ts 76 wattsx600-24Ts/XP 76 wattsx600-48Ts 123 wattsx600-48T

x600 Layer 3 Gigabit Ethernet Switch Installation Guide67RJ-45 Twisted Pair Port PinoutsFigure 31 illustrates the pin layout of an RJ-45 connector and

Appendix A: Technical Specifications68Table 12 lists the pin signals when a port operating at 1000 Mbps.Table 12. Pin Signals - 1000 MbpsPinout Pair1P

x600 Layer 3 Gigabit Ethernet Switch Installation Guide69RJ-45 Style Serial Terminal Port PinoutsTable 13 lists the pin signals on the RJ-45 style ser

7PrefaceThis guide contains the installation instructions for the x600 Series Layer 3 Gigabit Ethernet Switches. This preface contains the following s

Appendix A: Technical Specifications70RPS 21-pin D-combo Port and Connector PinoutsFigure 32 illustrates the pin layout of the RPS 21-pin D-combo port

x600 Layer 3 Gigabit Ethernet Switch Installation Guide7116 Ground17 Ground18 +12.0 VDC sense19 Ground20 No connectA-1 +12.0 VDCTable 14. RPS 21-pin C

Appendix A: Technical Specifications72

Preface8Product DocumentationFor overview information about the software features of the AlliedWare PlusTM Operating System Software which runs on the

x600 Layer 3 Gigabit Ethernet Switch Installation Guide9Starting a Management SessionFor instructions that describe how to start a local management se