613-000707 Rev. C10-GigabitEthernet SwitchAT-10408XPInstallation Guide
Tables10
11PrefaceThis guide contains instructions on how to install the AT-10408XP 10 Gigabit Ethernet Switch. This preface contains the following sections:
Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide13Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis produc
Preface14Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate infor
15Chapter 1OverviewThe AT-10408XP 10-Gigabit Ethernet Switch is designed to simplify the task of expanding an Ethernet, Fast Ethernet, or Gigabit Ethe
Chapter 1: Overview16FeaturesThe features of the AT-10408XP 10-Gigabit Ethernet Switch include: Port status LEDs Eight XFP (10 Gigabit small form fa
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide17Front and Back PanelsFigure 1 illustrates the front panel of the AT-10408XP 10-Gigabit Ether
Chapter 1: Overview18PortsThe AT-10408XP 10-Gigabit Ethernet Switch features the following ports: eight XFP ports, one 10/100/1000Base-T in-band manag
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide19LEDs The AT-10408XP 10-Gigabit Ethernet Switch has four groups of LEDs, as defined in the fo
Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied
Chapter 1: Overview20SD Card SlotLEDThe SD card slot has one LED as shown in Figure 5 and described in Table 3.Figure 5. SD Card Slot LEDTable 2. M
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide21Status LEDs The status LEDs are shown in Figure and described in Table 4. Figure 6. Status
Chapter 1: Overview22Power Supplies and FanThe switch has two rear power supply slots, which can accommodate the following combinations of power suppl
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide23Figure 8. AT-PWR02 PSU, AC Only1210AT-PWR02AC Power SupplyPWRGOODFAULTAC INPUT100-240VAC50/
Chapter 1: Overview24XFP TransceiversThe AT-10408XP 10-Gigabit Ethernet Switch supports the 10GBase-R XFP models listed in Table 5. Table 5. Support
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide25Network TopologyFigure 9 illustrates deploying the AT-10408XP 10-Gigabit Ethernet Switch for
Chapter 1: Overview26
27Chapter 2InstallationThis chapter contains the following sections: “Reviewing Safety Precautions” on page 28 “Selecting a Site for the Switch” on
Chapter 2: Installation28Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis or any of
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide29Circuit Overloading: Consideration should be given to the connection of the equipment to the
3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-
Chapter 2: Installation30Selecting a Site for the SwitchObserve the following requirements when choosing a site for your switch: If you plan to insta
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide31Unpacking the SwitchTo unpack the switch, perform the following procedure:1. Remove all comp
Chapter 2: Installation32Installing the Switch on a DesktopYou can place AT-10408XP 10-Gigabit Ethernet Switch on a desktop or install it in a 19-inch
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide33Installing the Switch in a RackTo install the AT-10408XP 10-Gigabit Ethernet Switch in a rac
Chapter 2: Installation344. Mount the switch on a 19-inch rack using four screws (not included), as shown in Figure 11 Figure 11. Mounting the Switch
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide35Circuit Overloading: Consideration should be given to the connection of the equipment to the
Chapter 2: Installation36Installing an XFP TransceiverThe AT-10408XP 10-Gigabit Ethernet Switch has eight XFP ports.NoteThe transceiver can be hot-swa
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide374. Slide the XFP transceiver into an XFP slot on the switch, as shown in Figure 13.Figure 13
Chapter 2: Installation38Cabling and Powering On the SwitchConnecting aXFP Fiber OpticCableTo connect a fiber optic cable to an XFP installed in the A
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide39Connecting the10/100/1000Base-T In-bandManagementPortTo connect the cable to the 10/100/1000
4Translated Safety StatementsImportant: The indicates that a translation of the safety statements is available in a PDF document titled “Translated
Chapter 2: Installation40NoteFor the terminal port pinouts, refer to “RJ-45 Style RS-232 Terminal Port Pinouts” on page 48.Powering On theSwitchTo pow
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide41Starting a Local Management SessionTo start a local management session on an AT-10408XP 10-G
Chapter 2: Installation42A command line prompt is displayed in Figure 20.Figure 20. Command Line Login ScreenThe default switch name is “(none)” and t
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide43Warranty RegistrationAllied Telesis hardware products are covered under limited warranties.
Chapter 2: Installation44
45Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the switch in the event that a problem occurs.NoteIf you need furth
Chapter 3: Troubleshooting46
47Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: 440 mm x 438mm x 43.6 mm(17.36 in x 17.36 in x 1.72 in)Weight: As shipped: 5.85
Appendix A: Technical Specifications48RJ-45 Style RS-232 Terminal Port PinoutsFigure 1 illustrates the pin layout and Table 1 describes the pinouts fo
AT-10408XP 10-Gigabit Ethernet Switch Installation Guide49In-band Management Port CablingTable 2 contains the cabling specifications for the in-band m
5Preface ...
Appendix A: Technical Specifications50
Contents6
7Figure 1. AT-10408XP Front Panel ...
Figures8
9Table 1. Safety Symbols ..............................
Comments to this Manuals