Allied-telesis AT-S63 User Manual Page 140
- Page / 430
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 11: Event Logs and Syslog Servers
140 Section II: Advanced Operations
Displaying Events This procedure explains how to display the events in an event log. You
can view all or just specific events of a log.
To view the events in an event log, perform the following procedure:
1. From the home page, select either Monitoring or Configuration.
2. From the Configuration menu, select the System option.
3. Select the Event Log tab.
The Event log tab is shown in Figure 37 on page 139.
4. Configure the parameters in the Display Filter Settings of the tab
according to the types of events to be displayed.
5. After configuring the parameters, click View.
The parameters in the Display Filter Settings section are defined here:
Log Location
Defines the event log to be viewed: Options are:
Temporary (Memory) - Displays the events from the log stored in
temporary memory. This log stores approximately 4,000 events.
Select this option if the switch has been running for some time
without a reset or power cycle. This is the default.
Permanent (NVS) - Displays the events from the log stored in
nonvolatile memory, which stores up to 2,000 events. Select this
option to view the events that occurred prior to a recent reset or
power cycle.
Severity Selections
Defines the severity of the events to be displayed. You can select more
than one severity by using the Ctrl key when making your selections.
The default is error, warning, and information events. Options are:
D - Debug - Debug messages provide detailed high-volume
information only intended for technical support personnel.
E - Error - Only error messages are displayed. Error messages
indicate that the switch operation is severely impaired.
W - Warning - Only warning messages are displayed. These
messages indicate that an issue may require manager attention.
I - Information - Only informational messages are displayed.
Informational messages display useful information that you can
ignore during normal operation.
ALL - Messages of all severity levels are displayed.
- Web Browser Interface 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 18
- Document Conventions 19
- Contacting Allied Telesyn 21
- History of New Features 22
- GUESTVLAN parameter for 23
- VLANASSIGNMENT and 23
- MACBASED parameter for 23
- Supplicant Mode for 25
- Basic Operations 27
- Chapter 1 29
- Switch’s IP Address 33
- Web Browser Tools 36
- Redundant Twisted Pair Ports 39
- Basic Switch Parameters 43
- Rebooting a Switch 51
- Pinging a Remote System 52
- Displaying System Information 57
- Enhanced Stacking 61
- Chapter 3: Enhanced Stacking 62
- Manage the master switch 66
- Chapter 4: SNMPv1 and SNMPv2c 70
- Chapter 5: Port Parameters 82
- Figure 21. Port Status Page 88
- Displaying Port Statistics 89
- Chapter 6: MAC Address Table 100
- Creating a Static Port Trunk 104
- Chapter 7: Static Port Trunks 106
- Modifying a Static Port Trunk 108
- Deleting a Port Trunk 110
- Displaying the Port Trunks 111
- The ports of the trunk 112
- Port Mirroring 113
- Creating a Port Mirror 114
- Section I: Basic Features 115 115
- Modifying a Port Mirror 117
- Disabling a Port Mirror 118
- Deleting a Port Mirror 119
- Displaying the Port Mirror 120
- Advanced Operations 121
- File System 123
- Chapter 9: File System 124
- File Downloads and Uploads 129
- Downloading a File 130
- Uploading a File 134
- Event Logs and Syslog Servers 137
- Working with the Event Logs 138
- Clearing an 144
- Event Log 144
- Modifying the 145
- Event Log Full 145
- Saving an Event 146
- Log to a File 146
- Configuring a 147
- Syslog Output 147
- Definition 147
- Viewing a Syslog 150
- Output Definition 150
- Modifying a 150
- Deleting a Syslog 151
- Classifiers 153
- Configuring a Classifier 154
- Chapter 12: Classifiers 156
- Modifying a Classifier 160
- Deleting a Classifier 162
- Displaying the Classifiers 163
- Class of Service 173
- Configuring CoS 174
- Chapter 14: Class of Service 176
- Configuring Egress Scheduling 178
- Displaying the CoS Settings 179
- Managing Flow Groups 184
- Modifying a Flow 187
- Deleting a Flow 188
- Displaying the 188
- Flow Groups 188
- Managing Traffic Classes 190
- Traffic Class 194
- Deleting a Traffic 196
- Traffic Classes 196
- Managing Policies 198
- Denial of Service Defense 205
- Displaying the DoS Settings 209
- IGMP Snooping 211
- Configuring IGMP Snooping 212
- Chapter 17: IGMP Snooping 214
- 220 Section III: SNMPv3 220
- Section III: SNMPv3 223 223
- Section III: SNMPv3 225 225
- Section III: SNMPv3 227 227
- Deleting a User 229
- Table Entry 229
- Section III: SNMPv3 231 231
- Section III: SNMPv3 233 233
- Section III: SNMPv3 235 235
- Deleting a View 237
- Modifying a View 237
- 1.3.6.1.2.1.2.2.1.0.3 238
- Section III: SNMPv3 239 239
- Creating an 240
- Access Table 240
- Chapter 18: SNMPv3 242
- 242 Section III: SNMPv3 242
- Modifying an 244
- Section III: SNMPv3 245 245
- Creating a 247
- SecurityToGroup 247
- 248 Section III: SNMPv3 248
- 252 Section III: SNMPv3 252
- 254 Section III: SNMPv3 254
- Notify Table 256
- Section III: SNMPv3 257 257
- Section III: SNMPv3 259 259
- 260 Section III: SNMPv3 260
- Modifying Target 262
- Address Table 262
- Section III: SNMPv3 263 263
- Creating a Target 265
- Parameters Table 265
- 266 Section III: SNMPv3 266
- Deleting a Target 268
- 270 Section III: SNMPv3 270
- Community 272
- Section III: SNMPv3 273 273
- Section III: SNMPv3 275 275
- Section III: SNMPv3 277 277
- Section III: SNMPv3 279 279
- Displaying View 280
- Table Entries 280
- Displaying Access 281
- Displaying 282
- Displaying Notify 283
- Displaying Target 284
- Section III: SNMPv3 287 287
- Spanning Tree Protocols 289
- Protocols 291
- Configuring STP 294
- Port Settings 297
- STP Settings 298
- 4. Click View 299
- Resetting STP to 300
- Settings 300
- Configuring RSTP 302
- Configuring 305
- RSTP Port 305
- Displaying RSTP 306
- Resetting RSTP 309
- Chapter 20 311
- Enabling MSTP 312
- Configuring MSTP 314
- Configuring the 317
- CIST Priority 317
- Managing MSTIs 318
- External path cost 322
- 10 Mbps 20,000 325
- 100 Mbps 20,000 325
- 1000 Mbps 2,000 325
- Virtual LANs 333
- 334 Section V: VLANs 334
- 336 Secton V: Virtual LANs 336
- 338 Secton V: Virtual LANs 338
- 340 Secton V: Virtual LANs 340
- 342 Secton V: Virtual LANs 342
- Selecting a VLAN Mode 344
- Displaying VLANs 345
- 346 Secton V: Virtual LANs 346
- 348 Secton V: Virtual LANs 348
- Configuring GVRP 350
- Section V: Virtual LANs 351 351
- Section V: Virtual LANs 353 353
- Displaying the GVRP Database 355
- Table 12 356
- Section V: Virtual LANs 357 357
- Displaying the GVRP Counters 359
- 360 Section V: Virtual LANs 360
- 362 Section V: Virtual LANs 362
- 364 Section VI: Port Security 364
- Configuring Port Security 366
- Section VI: Port Security 367 367
- Section VI: Port Security 369 369
- 370 Section VI: Port Security 370
- Setting Port Roles 372
- Section VI: Port Security 373 373
- Section VI: Port Security 375 375
- Section VI: Port Security 377 377
- 380 Section VI: Port Security 380
- 382 Section VI: Port Security 382
- 384 Section VI: Port Security 384
- 386 Section VI: Port Security 386
- Accounting 388
- Management Security 389
- Encryption Keys, PKI, and SSL 391
- Displaying the SSL Settings 397
- Secure Shell (SSH) 399
- Configuring SSH 400
- Displaying the SSH Settings 402
- TACACS+ and RADIUS Protocols 405
- Chapter 28 417
- Creating an ACE 420
- Deleting an ACE 422
Related products and manuals for Computer hardware Allied-telesis AT-S63
(2 pages)
(14 pages)© 2020, manymanuals.com. All rights reserved. | 0.313 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals