Allied-telesis AT-S63 User Manual Page 83
- Page / 430
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AT-S63 Management Software Web Browser Interface User’s Guide
Section I: Basic Operations 83
Possible settings are:
Auto-Negotiate: The port autonegotiates both speed and duplex mode.
This is the default.
10Mbps - Half Duplex
10Mbps - Full Duplex
100Mbps - Half Duplex
100Mbps - Full Duplex
1Gb - Full Duplex (Applies only to 1000Base SFP and GBIC modules.
This selection should not be used. An SFP or GBIC module should use
Auto-Negotiation to set its speed and duplex mode.)
Note
A 10/100/1000Base-T twisted pair port must be set to Auto-
Negotiation to operate at 1000 Mbps. You cannot manually configure
a 10/100/1000Base-T twisted pair port to 1000 Mbps.
MDI/MDIX Crossover
The wiring configuration of a twisted pair port. This parameter does not
apply to fiber optic ports. Possible settings are:
Auto - Sets the port to automatically configure itself as MDI or
MDIX, depending upon the end node. This is the default. This
setting is only available when a port is set to Auto-Negotiation.
MDI - Sets a port to MDI. This setting is only available when a
port’s speed and duplex mode are set manually.
MDIX - Sets a port to MDIX. This setting is only available when a
port’s speed and duplex mode are set manually.
Ingress Broadcast Filter
Use this parameter to configure a port to forward or discard ingress
broadcast packets. Possible settings are:
Enabled - The port discards ingress broadcast packets.
Disabled - The port forwards ingress broadcast packets. This is the
default setting.
Egress Broadcast Filter
Use this parameter to configure a port to forward or discard egress
broadcast packets. Possible settings are:
Enabled - The port discards egress broadcast packets.
Disabled - The port forwards egress broadcast packets. This is the
default setting.
- Web Browser Interface 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 18
- Document Conventions 19
- Contacting Allied Telesyn 21
- History of New Features 22
- GUESTVLAN parameter for 23
- VLANASSIGNMENT and 23
- MACBASED parameter for 23
- Supplicant Mode for 25
- Basic Operations 27
- Chapter 1 29
- Switch’s IP Address 33
- Web Browser Tools 36
- Redundant Twisted Pair Ports 39
- Basic Switch Parameters 43
- Rebooting a Switch 51
- Pinging a Remote System 52
- Displaying System Information 57
- Enhanced Stacking 61
- Chapter 3: Enhanced Stacking 62
- Manage the master switch 66
- Chapter 4: SNMPv1 and SNMPv2c 70
- Chapter 5: Port Parameters 82
- Figure 21. Port Status Page 88
- Displaying Port Statistics 89
- Chapter 6: MAC Address Table 100
- Creating a Static Port Trunk 104
- Chapter 7: Static Port Trunks 106
- Modifying a Static Port Trunk 108
- Deleting a Port Trunk 110
- Displaying the Port Trunks 111
- The ports of the trunk 112
- Port Mirroring 113
- Creating a Port Mirror 114
- Section I: Basic Features 115 115
- Modifying a Port Mirror 117
- Disabling a Port Mirror 118
- Deleting a Port Mirror 119
- Displaying the Port Mirror 120
- Advanced Operations 121
- File System 123
- Chapter 9: File System 124
- File Downloads and Uploads 129
- Downloading a File 130
- Uploading a File 134
- Event Logs and Syslog Servers 137
- Working with the Event Logs 138
- Clearing an 144
- Event Log 144
- Modifying the 145
- Event Log Full 145
- Saving an Event 146
- Log to a File 146
- Configuring a 147
- Syslog Output 147
- Definition 147
- Viewing a Syslog 150
- Output Definition 150
- Modifying a 150
- Deleting a Syslog 151
- Classifiers 153
- Configuring a Classifier 154
- Chapter 12: Classifiers 156
- Modifying a Classifier 160
- Deleting a Classifier 162
- Displaying the Classifiers 163
- Class of Service 173
- Configuring CoS 174
- Chapter 14: Class of Service 176
- Configuring Egress Scheduling 178
- Displaying the CoS Settings 179
- Managing Flow Groups 184
- Modifying a Flow 187
- Deleting a Flow 188
- Displaying the 188
- Flow Groups 188
- Managing Traffic Classes 190
- Traffic Class 194
- Deleting a Traffic 196
- Traffic Classes 196
- Managing Policies 198
- Denial of Service Defense 205
- Displaying the DoS Settings 209
- IGMP Snooping 211
- Configuring IGMP Snooping 212
- Chapter 17: IGMP Snooping 214
- 220 Section III: SNMPv3 220
- Section III: SNMPv3 223 223
- Section III: SNMPv3 225 225
- Section III: SNMPv3 227 227
- Deleting a User 229
- Table Entry 229
- Section III: SNMPv3 231 231
- Section III: SNMPv3 233 233
- Section III: SNMPv3 235 235
- Deleting a View 237
- Modifying a View 237
- 1.3.6.1.2.1.2.2.1.0.3 238
- Section III: SNMPv3 239 239
- Creating an 240
- Access Table 240
- Chapter 18: SNMPv3 242
- 242 Section III: SNMPv3 242
- Modifying an 244
- Section III: SNMPv3 245 245
- Creating a 247
- SecurityToGroup 247
- 248 Section III: SNMPv3 248
- 252 Section III: SNMPv3 252
- 254 Section III: SNMPv3 254
- Notify Table 256
- Section III: SNMPv3 257 257
- Section III: SNMPv3 259 259
- 260 Section III: SNMPv3 260
- Modifying Target 262
- Address Table 262
- Section III: SNMPv3 263 263
- Creating a Target 265
- Parameters Table 265
- 266 Section III: SNMPv3 266
- Deleting a Target 268
- 270 Section III: SNMPv3 270
- Community 272
- Section III: SNMPv3 273 273
- Section III: SNMPv3 275 275
- Section III: SNMPv3 277 277
- Section III: SNMPv3 279 279
- Displaying View 280
- Table Entries 280
- Displaying Access 281
- Displaying 282
- Displaying Notify 283
- Displaying Target 284
- Section III: SNMPv3 287 287
- Spanning Tree Protocols 289
- Protocols 291
- Configuring STP 294
- Port Settings 297
- STP Settings 298
- 4. Click View 299
- Resetting STP to 300
- Settings 300
- Configuring RSTP 302
- Configuring 305
- RSTP Port 305
- Displaying RSTP 306
- Resetting RSTP 309
- Chapter 20 311
- Enabling MSTP 312
- Configuring MSTP 314
- Configuring the 317
- CIST Priority 317
- Managing MSTIs 318
- External path cost 322
- 10 Mbps 20,000 325
- 100 Mbps 20,000 325
- 1000 Mbps 2,000 325
- Virtual LANs 333
- 334 Section V: VLANs 334
- 336 Secton V: Virtual LANs 336
- 338 Secton V: Virtual LANs 338
- 340 Secton V: Virtual LANs 340
- 342 Secton V: Virtual LANs 342
- Selecting a VLAN Mode 344
- Displaying VLANs 345
- 346 Secton V: Virtual LANs 346
- 348 Secton V: Virtual LANs 348
- Configuring GVRP 350
- Section V: Virtual LANs 351 351
- Section V: Virtual LANs 353 353
- Displaying the GVRP Database 355
- Table 12 356
- Section V: Virtual LANs 357 357
- Displaying the GVRP Counters 359
- 360 Section V: Virtual LANs 360
- 362 Section V: Virtual LANs 362
- 364 Section VI: Port Security 364
- Configuring Port Security 366
- Section VI: Port Security 367 367
- Section VI: Port Security 369 369
- 370 Section VI: Port Security 370
- Setting Port Roles 372
- Section VI: Port Security 373 373
- Section VI: Port Security 375 375
- Section VI: Port Security 377 377
- 380 Section VI: Port Security 380
- 382 Section VI: Port Security 382
- 384 Section VI: Port Security 384
- 386 Section VI: Port Security 386
- Accounting 388
- Management Security 389
- Encryption Keys, PKI, and SSL 391
- Displaying the SSL Settings 397
- Secure Shell (SSH) 399
- Configuring SSH 400
- Displaying the SSH Settings 402
- TACACS+ and RADIUS Protocols 405
- Chapter 28 417
- Creating an ACE 420
- Deleting an ACE 422
Related products and manuals for Computer hardware Allied-telesis AT-S63
(2 pages)
(14 pages)© 2020, manymanuals.com. All rights reserved. | 0.570 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals