Allied-telesis AT-MC605 User Manual

613-001153 Rev. CVDSL Ethernet ExtenderAT-MC605 Installation Guide

Tables10

11PrefaceThis guide contains instructions on how to install the AT-MC605 VDSL Ethernet Extender and contains the following sections: “Safety Symbols

Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-MC605 VDSL Ethernet Extender Installation Guide13Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are

Preface14Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate inform

15Chapter 1OverviewThe AT-MC605 VDSL Ethernet Extended product is designed to transmit and receive data at very high speeds over unshielded pairs of c

Overview16Summary of FeaturesThe AT-MC605 VDSL Ethernet Extender provides the following features: VDSL (Very high-bit-rate Digital Subscriber) protoc

AT-MC605 VDSL Ethernet Extender Installation Guide17Figure 2. illustrates the rear panels of the AT-MC605 VDSL Ethernet Extender.Figure 2. AT-MC605 Re

Overview18AT-MC605 Port DescriptionsVDSL Line Port The VDSL Line port features an RJ-11 connector. It allows you to connect two AT-MC605 VDSL Ethernet

AT-MC605 VDSL Ethernet Extender Installation Guide1910Base-T/100Base-TxEthernet PortThe AT-MC605 VDSL Ethernet Extender has one 10Base-T/100Base-Tx et

Copyright 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Te

Overview20ethernet port is set to 100 Mbps.Half- and Full-duplex ModeDuplex mode refers to the way an end-node sends and receives data on the network.

AT-MC605 VDSL Ethernet Extender Installation Guide21RJ-45 Port PinoutsThe pin assignments of an RJ-45 10Base-T/100Base-TX connector and port are illus

Overview22Status LEDsThe AT-MC605 VDSL Ethernet Extender features the status LEDs and are defined in Table 5.Table 5. Front Panel Status LEDsLED Color

AT-MC605 VDSL Ethernet Extender Installation Guide23RATE Blinking GREEN/After a VDSL link is established, the Rate LED will continuously blink a set n

Overview24VDSL Configuration DIP SwitchesVDSL SwitchDefinitionsThe AT-MC605 VDSL Ethernet Extender features the four VDSL Configuration DIP switches o

AT-MC605 VDSL Ethernet Extender Installation Guide25The front panel VDSL Configuration DIP switches are shown in Figure 4Figure 4. VDSL Configuration

Overview26NO LIMIT/RATE LIMIT VDSL Configuration SwitchThe NO LIMIT/RATE LIMIT (Right Center) switch selects the maximum data rate for the VDSL line.

AT-MC605 VDSL Ethernet Extender Installation Guide27External AC/DC Power AdapterAn external, energy efficient, AC/DC power adapter is included with th

Overview28Multiple Dwelling Unit (MDU) TopologyThe AT-MC605 Ethernet Extender can be used in multi-dwelling units (MDU), multi-tenant buildings (MTU),

AT-MC605 VDSL Ethernet Extender Installation Guide29individually assigned to each dorm room. The Provider units are rack mounted together in AT-MCR12

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class B, EN55022 Class B, EN61000-3-2, EN61000-

30Chapter 2InstallationThis chapter contains the installation procedures for the AT-MC605 VDSL Ethernet Extender in the following sections: “Reviewin

AT-MC605 VDSL Ethernet Extender Installation Guide31Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to ins

Overview32Selecting a Site for the AT-MC605 Ethernet ExtenderObserve the following requirements when choosing a site for your AT-MC605 VDSL Ethernet E

AT-MC605 VDSL Ethernet Extender Installation Guide33Required CablingThe AT-MC605 VDSL Ethernet Extender requires two or more of the three cables descr

Overview34Unpacking the AT-MC605 Ethernet ExtenderTo unpack the AT-MC605 product:1. Remove all components from the shipping package and store the pack

AT-MC605 VDSL Ethernet Extender Installation Guide35Installing the AT-MC605 VDSL Ethernet Extender Subscriber UnitThe AT-MC605 Subscriber unit is norm

Overview365. Go to “Cabling the Subscriber Unit” on page 36 to connect the cables and to “Powering On the Subscriber Unit” on page 38 for powering the

AT-MC605 VDSL Ethernet Extender Installation Guide372. To connect a telephone to the AT-MC605 Ethernet Extender, connect a telephone line cable from t

Overview38Powering On theSubscriber UnitPower on the Subscriber unit using the power adapter provided, as shown in Figure 11.Figure 11. Power On The S

AT-MC605 VDSL Ethernet Extender Installation Guide39Installing the AT-MC605 Ethernet Extender Provider UnitThe AT-MC605 Provider unit can either be in

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

Overview403. Configure the right VDSL CONFIG switch (SCBR/PROV) to the SCBR position as shown in Figure 13.Figure 13. Configuring AT-MC605 Ethernet Ex

AT-MC605 VDSL Ethernet Extender Installation Guide41Rack-Mountingthe Provider UnitTo install the Provider unit in an AT-MCR12 rackmount chassis, perfo

Overview423. Position the slider, as shown in Figure 16 and push into the chassis.Figure 16. Rack Mount - Set in Rack4. To connect the cables, see “Ca

AT-MC605 VDSL Ethernet Extender Installation Guide432. Connect a telephone line cable from the Phone port to the building PBX connection as shown in F

Overview44Powering On theProvider UnitIf you have rack mounted the AT-MC605 Provider unit, the host equipment, AT-MCR12 rackmount chassis, is must be

45Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the AT-MC605 VDSL Ethernet Extender in the event a problem occurs.N

Overview46OFF, do the following: Verify that the end node connected to the port is powered ON and is operating properly. Check that the twisted pair

47Appendix ATechnical SpecificationsPhysical SpecificationsDimensions: (W x D x H)109 mm x 95 mm x 25 mm(4.29 in. x 3.74 in. x 0.98 in.)Weight: .3 kg

Appendix A: Technical Specifications48Safety and Electromagnetic Compatibility CertificationsEmission: EN55022 Class B, FCC Part 15 Class BImmunity: E

5Preface ...

Contents6

7List of FiguresFigure 1. AT- MC605 Front Panel...

Figures8

9Table 1. Safety Symbols ..............................