Allied Telesis AT-8000GS User's Guide Page 197
- Page / 205
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Downloading Software with CLI
Initial Configuration
Page 197
Initial Configuration
Before a device can download system software, the device must have an initial configuration of IP address and
network mask.
Before assigning a static IP address to the device, obtain the following information from the network administrator:
• A specific IP address allocated by the network administrator for the switch to be configured
• Network mask for the network
After making any configuration changes, the new configuration must be saved before rebooting. To save the
configuration, enter the following CLI command: The following prompt is displayed:
Configuration
The initial configuration, which starts after the device has booted successfully, includes static IP address and
subnet mask configuration, and setting user name and privilege level to allow remote management. If the device is
to be managed from an SNMP-based management station, SNMP community strings must also be configured.
The following basic configurations are required:
• "Static IP Address and Subnet Mask"
• "User Name"
Static IP Address and Subnet Mask
IP interfaces can be configured on each port of the device. After entering the configuration command, it is
recommended to check if a port was configured with the IP address by entering the “show ip interface” command.
The commands to configure the device are port specific.
To manage the switch from a remote network, a static route must be configured, which is an IP address to where
packets are sent when no entries are found in the device tables. The configured IP address must belong to the
same subnet as one of the device IP interfaces.
To configure a static route, enter the required commands at the system prompt as shown in the following
configuration example where 101.101.101.101 is the specific management station, and 5.1.1.100 is the static
route:
Note
100.1.1.33 is the IP address of the next hop that can be used to reach the management network
192.168.2.0.
Console#
copy running-config startup-config
Console#
configure
Console(config)#
interface vlan
1
Console(config-if)#
ip address
100.101.101.101 255.255.255.0
Console(config-if)#
exit
Console#
ip route
192.168.2.0/24 100.1.1.33
- Web Browser Interface 1
- User’s Guide 1
- Contents 3
- Intended Audience 8
- Document Conventions 8
- Contacting Allied Telesis 8
- Section 1. Getting Started 9
- Getting Started 10
- Figure 2: System General Page 10
- User Interface Components 12
- Using the Management Buttons 13
- Figure 5: Add Local User Page 14
- Logging Out 15
- Resetting the Device 16
- Setting the System Clock 19
- Configuring SNTP 20
- Broadcast Time Information 21
- Configuring System Time 24
- Configuring Device Security 25
- • Defining Access Control 25
- Defining Access Profiles 26
- Defining Profile Rules 30
- Configuring TACACS+ 38
- Configuring RADIUS 41
- Configuring Local Users 44
- Defining Line Passwords 46
- Configuring Network Security 47
- Figure 29: Port Security Page 48
- Defining 802.1x Port Access 50
- Enabling Storm Control 53
- Defining Access Control 55
- Adding ACE Rules 57
- Defining IP Based ACL 60
- Defining ACL Binding 66
- Configuring DHCP Snooping 68
- • Defining Trusted Interfaces 68
- Defining Trusted Interfaces 71
- Section 6. Configuring Ports 75
- Configuring Ports 76
- Configuring Port Mirroring 79
- Aggregating Ports 82
- Defining Port Trunking 86
- Configuring LACP 88
- Defining MAC Addresses 90
- Configuring VLANs 93
- Defining VLAN Properties 94
- Defining GVRP 98
- Defining MAC Based Groups 100
- Page 101 101
- Configuring Interfaces 102
- Defining Log Settings 103
- Page 104 104
- Adding Log Servers 105
- Modifying Log Servers 106
- Page 107 107
- Page 108 108
- Defining STP Properties 109
- Page 110 110
- Defining STP Interfaces 111
- Page 112 112
- Configuring Spanning Tree 113
- Page 114 114
- Page 115 115
- Defining MSTP Properties 116
- Defining MSTP Interfaces 117
- Page 118 118
- Page 121 121
- • Configuring IGMP Snooping 123
- Configuring IGMP Snooping 124
- Page 125 125
- Page 126 126
- Page 127 127
- Page 128 128
- Page 129 129
- Page 130 130
- Section 11. Configuring SNMP 131
- Page 132 132
- Enabling SNMP 133
- Defining SNMP Communities 134
- SNMP Communities Basic Table 135
- Page 136 136
- Configuring SNMP 137
- Defining SNMP Groups 138
- Figure 103:Add Group Page 139
- Defining SNMP Users 140
- Page 141 141
- Defining SNMP Views 143
- Figure 109:Add SNMP VIew Page 144
- Page 145 145
- SNMPv3 Notification Recipient 146
- Figure 111: Add Notify Page 147
- Defining Notification Filters 149
- Page 150 150
- Page 151 151
- Page 152 152
- Page 153 153
- Page 154 154
- Page 155 155
- Page 156 156
- Page 157 157
- Page 158 158
- Mapping CoS Values to Queues 159
- Mapping DSCP Values to Queues 160
- Configuring QoS Bandwidth 161
- Page 162 162
- Section 14. System Utilities 163
- Page 164 164
- Page 165 165
- Page 166 166
- Page 167 167
- System Utilities 168
- Viewing Optical Transceivers 169
- Viewing Device Statistics 171
- Page 172 172
- Viewing Etherlike Statistics 173
- Page 174 174
- Managing RMON Statistics 175
- Page 176 176
- Configuring RMON History 177
- Viewing Statistics 178
- Page 179 179
- Page 180 180
- Configuring RMON Events 181
- Viewing the RMON Events Logs 183
- Defining RMON Alarms 184
- Page 185 185
- Section 16. Managing Stacking 187
- Stacking Chain Topology 188
- Stacking Members and Unit ID 188
- Exchanging Stacking Members 189
- Managing Stacking 190
- Figure 144:Stacking Page 190
- Appendix A. System Defaults 191
- RS-232 Port Settings 192
- Port Defaults 192
- Security Defaults 193
- Jumbo Frame Defaults 193
- System Time Defaults 193
- Configuration Defaults 193
- Spanning Tree Defaults 194
- Address Table Defaults 194
- VLAN Defaults 194
- Trunking Defaults 195
- Multicast Defaults 195
- QoS Defaults 195
- Connecting a Terminal 196
- Initial Configuration 197
- Downloading Software 198
- Downloading Software with CLI 199
- Page 203 203
- Page 204 204
- Page 205 205
Related products and manuals for Network switches Allied Telesis AT-8000GS
(46 pages)
(38 pages)
(50 pages)
(38 pages)© 2020, manymanuals.com. All rights reserved. | 2.723 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals